Sidebench LabsShop Now
User guide

Smart aircon user guide

Set up your Smart Aircon Module, connect it to Apple Home, and find answers when something isn’t working.

01

Connect the smart aircon module

Before you start

You will need:

  • The smart aircon module with its attached cable.
  • A compatible Mitsubishi Electric aircon.
  • Your home Wi-Fi name and password. The network must support 2.4 GHz.

Watch the installation

Installation video · 3:46 · Captions are shown on screen

Connect the cable

  1. Turn off the electrical supply. Follow your aircon’s installation instructions before removing any covers.
  2. Open the aircon casing. Remove the screws on both sides of the swing flap, unclip the swing flap, then lift off the front cover. Some models also have a screw under the front panel, beside the filter. Remove it too.
  3. Plug in the cable. One end is already attached to the module. Where the CN105 port is depends on your model:
    1. On the control board. The board is visible on the right once the front cover is off. Gently connect the plug to the red CN105 socket, then tuck the module and cable into the bottom of the case.
    2. Inside the metal box. If the board is enclosed in a metal box on the right, unscrew and unclip its cover. Gently connect the plug to the red CN105 socket, tuck the module and cable inside so the cover can close, then refit the cover and its screws.
  4. Close all covers, then restore power. Refit the front cover, swing flap and screws, then switch the power back on. The module starts automatically using power from the aircon. No separate power supply is needed. If the module’s green light blinks and the aircon won’t turn on, the swing flap isn’t secured: lock its louver holder and try again.
Important
Use only the supplied cable. Do not connect the USB-C cable while the module is connected to the aircon.

More than one aircon?

Set up one smart aircon module at a time. Note which module belongs to each room so you can name it correctly in Apple Home.

02

Connect to your home Wi-Fi

Watch the setup

Wi-Fi and Apple Home setup video · 1:19 · Covers this section and the next

Open the setup page

  1. Open your phone’s Wi-Fi settings near the smart aircon module.
  2. Join the module’s setup network using the details below.
  3. Stay connected if your phone says No Internet. This is normal during setup.
  4. Open the page that appears. If it does not open, enter http://192.168.4.1 in your browser’s address bar.
Setup detailWhat to enter
Wi-Fi networkSidebench-XXXX XXXX is different for each module
Wi-Fi passwordsidebench
Setup pagehttp://192.168.4.1

Follow the on-screen steps

  1. Read the introduction, then continue.
  2. Choose your home Wi-Fi and enter its password. If the connection fails, check the details and try again.
  3. Save the eight-digit pairing code. Take a screenshot or write it down, then tap I’ve saved the code - Finish.
  4. Reconnect your phone to your home Wi-Fi. You are ready to add the module to Apple Home.
03

Add to Apple Home

  1. Make sure your phone and the smart aircon module are connected to your home Wi-Fi.
  2. Open Home, tap +, then Add Accessory.
  3. Tap More options… and select Aircon XXXX, matching your module’s four characters.
  4. Dismiss the Uncertified accessory notification by tapping on Add anyway.
  5. Enter the eight-digit code saved during setup.
  6. Follow the prompts to choose a room and a name, such as Bedroom Aircon.
  7. Select Cool, set a temperature and check that the aircon responds.
04

Everyday use

Control your aircon in Apple Home.

SettingWhat it does
OffTurns the aircon off
CoolCools the room to your chosen temperature
Fan SpeedManual fan speed
Fan AutoAuto fan speed
Dry ModeSwitch to dry mode
Fan ModeSwitch to fan mode

Control when you are away

For Apple Home access away from home, you need a compatible Apple home hub. Follow Apple’s home hub setup guide.

05

Help and troubleshooting

ProblemTry this
The setup page will not openStay connected to the smart aircon module’s setup network and enter http://192.168.4.1 in your browser.
The module will not join my Wi-FiCheck the password is correct and that 2.4 GHz Wi-Fi is enabled.
The module does not appear when adding it to Apple HomeCheck that your phone is on the same home Wi-Fi network as the module, and that it is powered on.
Apple Home says Not RespondingCheck that your home Wi-Fi is working. Restart your phone and the Apple home hub before trying again.

Changed your router or Wi-Fi password?

Leave the module powered for about 5 minutes. Its setup network should reappear. Connect using the details in section 2 and enter your new home Wi-Fi details. Changing Wi-Fi does not remove your Apple Home pairing.

Factory reset

This erases everything
A factory reset erases everything the smart aircon module has stored: your home Wi-Fi details, your Apple Home pairing and all your settings.
  1. Press and hold the button on the module.
    Front of the smart aircon module. The button is the raised rectangle right above the M5 logo.
    The button is on the front of the module, right above the M5 logo.
  2. Wait for the light to flash red. This takes 10 seconds and means the reset is ready.
  3. Let go. The module erases everything and restarts.

After a reset, remove the old accessory from Apple Home before adding it back:

  1. Open the accessory in Apple Home.
  2. Scroll down to Bridge.
  3. Click on Remove Bridge from Home.

Then, set up the module again from section 2.

06

What the lights mean

Quick fix
If a light suggests something is wrong, turn the aircon’s power off, wait ten seconds, then turn it back on. This clears most faults.
LightWhat it means
Main light offNormal operation
White steadyStarting up
White slowly pulsingSmart aircon module is busy; leave the power on
White flashing quicklyIdentifying the module after Flash LED or Identify was selected
Blue slowly pulsingReady for Wi-Fi setup
Blue flashing quicklyConnecting to Wi-Fi
Small blue light onWi-Fi is disconnected
Green brieflyConnection or pairing successful
Red steadyCannot connect to the aircon. Check the cable is firmly connected at both ends, then turn the power off and on again.
Red flashingThe module will perform a factory reset — let go of the button and wait for it to restart
Yellow slowly pulsingThe module has restarted itself several times and is now waiting. Turn the power off and on again to clear it.